In short it said: SSDLIfe has not detected any SSD's on your comperter. i tried attaching a screenshot but can't even do that. Anybody have any ideals this one subject. Used to be Disk0 for the SSD since birth, this is in Disk Management The rest are fine, SSD's are (C in File Explorer, Oh and there (SSD) the first in line to Boot in the Bios. Having trouble keeping my SSD's in Disk0, my HDD's are Disk0 n Disk1, SSD are Disk2. There Adata XP900's 256Mb (x2), got them in 2014 march. It Boots FAST, my PC works likes it new but two test i did, one with Userbenchmark and one other ( i forget) gave my SSD's the thumbs down. I was on Raid0 but change to AHCI like it says, I rebooted with all the changes done, it still don't see them. i think there's something wrong because i downloaded SSDLife just to check my SSD drives, it downloaded, it's in my Programs/Features, but it won't start because it doesn't see them. Therefore, if you have an ADATA SSD and you have updated its firmware and, by doing so, the BIOS has stopped recognizing the SSD, what we recommend you do is immediately open a support ticket with the company to initiate an RMA, even if the SSD is no longer within the warranty period since in this case the problem is the fault of a manufacturer error.Well. We have consulted the ADATA warranty policy and they do not specify nor is there any mention of firmware updates, so we must understand that, in this case, a failure in the firmware update should be covered by the guarantee in the case that the unit is unusable as in this case (what they do specify is that they are not responsible for the data that the device contains). What should you do if your SSD crashes while updating the firmware?Īs a general rule, and although the manufacturer usually releases firmware updates with some frequency, if the SSD breaks down during this process it is not usually covered by the warranty. However, and as we have already mentioned, it is advisable not to update the firmware of the ADATA SSDs for now, and not only of the Gammix S70 and S70 Blade models but of any of the brand … better safe than sorry. Luckily, updating the firmware of the SSD is not something that users do very frequently (at least not as much as the graphics drivers, for example), so it seems that there are not many users affected. Obviously, explanations have been requested from the manufacturer, but they have not yet made any official communication. All functions are categorized into seven sub-screens, including Drive Information, Diagnostic Scan, Utilities, System Optimization, System Information, Benchmark and CloneDrive. Unzip the file and double-click SSDTool.exe to start. For this reason, if you have an ADATA SSD (whether or not it is the affected model) we recommend you not to update your firmware until the maker of explanations. Starting SSD Toolbox You can download ADATA SSD Toolbox from ADATA’s official website. However, a short time later, several users have reported that both with Gammix S70 models and with its sister model, the S70 Blade, after updating to this version of the firmware the equipment stopped recognizing the unit.Īfter contacting the manufacturer’s support, the latter advised another user not to update their SSD firmware until the problem was resolved, and ADATA automatically removed the update from their website (and is still available through from SSD ToolBox). Firmware that renders ADATA SSDs unusableĪt the end of July, ADATA launched the firmware 3.2.9.1 for your Gammix S70 SSDs, aiming to significantly improve drive performance when the SSD is more than 50% full. The problem is that after installing this update and restarting the system, the PC BIOS stops recognizing the solid state device, literally rendering it unusable. The firmware version mentioned is 3.2.9.1, and it could be accessed both from the manufacturer’s website and directly from their management software, SSD ToolBox.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |